|
|
|
|
 |
| |
Locknuts ER:
– Highest runout accuracy
– No wear and high clamping force due to special slide coating
– Small vibrations due to pre-balancing
– Version HS fine-balanced
Locknuts OZ:
– Inner ring with ball bearing
– High clamping forces
– Low unbalance due to symmetrical design | |
| |
|
Technical data subject to change without prior notice. | |
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
83.912...
|
|
INFO
|
|
DXF
INFO
|
|
DXF
INFO
|
|
DXF
INFO
|
|
DXF
INFO
|
|
DXF
INFO
|
|
|
|
|
|
|
|
|
|
|
HS Version 83.912...
|
|
|
|
DXF
INFO
|
|
INFO
|
|
DXF
INFO
|
|
DXF
INFO
|
|
DXF
INFO
|
|
|
|
|
|
|
|
|
|
|
Ø A
|
|
19
|
|
28
|
|
34
|
|
42
|
|
50
|
|
63
|
|
|
|
|
|
|
|
|
|
|
B
|
|
11,3
|
|
17
|
|
19
|
|
20
|
|
22,3
|
|
25,3
|
|
|
|
|
|
|
|
|
|
|
C
|
|
M 14 x 0,75
|
|
M 22 x 1,5
|
|
M 25 x 1,5
|
|
M 32 x 1,5
|
|
M 40 x 1,5
|
|
M 50 x 1,5
|
|
|
|
|
|
|
|
|
|
|
ER with slide bearing
|
|
|
|
|
|
|
|
ER 25
|
|
ER 32
|
|
ER 40
|
|
|
|
|
|
|
|
|
|
|
83.913...
|
|
|
|
|
|
|
|
DXF
INFO
|
|
DXF
INFO
|
|
INFO
|
|
|
|
|
|
|
|
|
|
|
Ø A
|
|
|
|
|
|
|
|
42
|
|
50
|
|
63
|
|
|
|
|
|
|
|
|
|
|
B
|
|
|
|
|
|
|
|
22
|
|
26
|
|
29
|
|
|
|
|
|
|
|
|
|
|
C
|
|
|
|
|
|
|
|
M 32 x 1,5
|
|
M 40 x 1,5
|
|
M 50 x 1,5
|
|
|
|
|
|
|
|
|
|
|
OZ with ball bearing
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Clamping range Ø [mm]
|
|
|
|
2–16
|
|
|
|
2–25
|
|
4–32
|
|
6–40
|
|
|
|
|
|
|
|
|
|
|
83.920...
|
|
|
|
DXF
INFO
|
|
|
|
DXF
INFO
|
|
DXF
INFO
|
|
DXF
INFO
|
|
|
|
|
|
|
|
|
|
|
ØA
|
|
|
|
43
|
|
|
|
60
|
|
72
|
|
85
|
|
|
|
|
|
|
|
|
|
|
B
|
|
|
|
24
|
|
|
|
30
|
|
33,5
|
|
37
|
|
|
|
|
|
|
|
|
|
|
C
|
|
|
|
M 33 x 1,5
|
|
|
|
M 48 x 2
|
|
M 60 x 2,5
|
|
M 68 x 2,5
|
|
|
| |
|
